Car Heater Not Working After Radiator Flush

May 05, 2021

I back flushed the heater core and it was clear and no restrictions. Temperature from the car heater outlets should be 130 degrees or more with the fan on high after the car has warmed up.

Cooling/Heater (With images) Austin healey

Please advise not sure what to do next other than test the wire itself that connects to said switch.

Car heater not working after radiator flush. The car oil did not have white residue due to radiator fluid leaking into the engine oil. Now it is clear that which time and condition a radiator flush good or bad. If input is hot and output is cold, then you either have a clogged core or a bad heater valve.

Turn the heat on, full blast. You will have to run the vehicle untill the heater is blowing hot air during the flush, that way its going through the thermostat. This is especially true if it has been a while since you last changed the coolant as all the buildup can eventually end up in the heater core.

Mostly, a vacuum leak can cause this too. For better clearance, lift up. Any advice would be appreciated.

If neither one is warm, then maybe air blockage or low coolant or sticking thermostat. If it sticks in the open position, there will be insufficient pressure in the system, and the coolant will not get hot enough, reducing the heater’s output. How to flush radiator with vinegar.

Now, if the engine/radiator is low on coolant the fan motor will not get the signal from the sensor to come on, so first start with checking the coolant level inside the radiator. Your radiator cap regulates the pressure in the cooling system, acting as an escape valve if the pressure gets too high. The inlet hose for the heater core is hot the exit hose is cool.

Do not stand in line with or near the engine cooling fan blade when revving the engine. Here are a few of the more common reasons that’s causing the car heater to not work properly: If the coolant is low, or there is an air lock (and also after replacing any faulty parts) you need to fill the system properly.

Let the car idle and keep pouring coolant into the radiator every time the level drops. If it isn't it could be that the heater control valve is not working and needs to be replaced, or on older cars a physical flap which alters the path of the air could be broken, or disconnected from the controls. Select the maximum heater temperature and blower motor speed settings.

Start the engine and allow it to idle. This may be due to a faulty heater blower motor or potentially a bad heater core. How to clean a clogged radiator properly:

It will be at the base of the radiator, in between the core and the main hose. Trying to take this truck across country and need the heater to stay warm until the summer. This process will clean out the heater core and bleed any air bubbles out of the cooling system.

Engine overheating can be caused by a number of things such as low coolant levels, a faulty thermostat, or a failing coolant fan switch. If one is hot and the other one is cooler, fluid is not passing through. You could test for a heater core clog by opening the hood and feeling the input and output hoses to the heater core.

When a radiator is clogged, the airflow will seize, and it may cause the car to overheat. Without any problem, radiator flush can harm the radiator. Prior to the flush i had no problems.

If your car’s heater doesn’t seem to be working too well, it might be time to flush it out. You should not flush the radiator but drain the fluid and refill it. Turn on the heater, if you do not have hot air coming out the vents, you are probably low on coolant in the radiator or there is some kind of restriction in the system like at the bottom of the radiator not allowing coolant to circulate.

When you face overheating or contaminant in the coolant, you should check the necessary cause for this problem. To do this, set the heater controls in the car to maximum heat, remove the radiator cap (or remote mounted coolant pressure cap, sometimes on. The car heater was working fine.

Do this for about fifteen minutes, and then you should have all of the air bubbles out of the system. Then if you see that radiator flush is the best solution, then you should do it for the efficiency of the radiator. Let us know what happens.

To check for this problem: A clogged or blocked radiator of your car could be redressed in a few easy steps which are as follows: Let the car cool for 15 to 20 minutes.

After a coolant flush, some of the debris or foreign particles can still get stuck inside the heater core. Heater control valve when you set the temperature to hot, air being passed over the heater matrix should be ducted into the cabin. When your vehicle’s engine has cooled down, open the radiator cap and check the level of coolant.

(some engines are aluminum) let stand for 4 hours. Take a bucket and place it under radiator drain petcock. Just replace the radiator cap with a new one.

While the engine of your car is cool enough, park it on a level platform. The heater not working in some cases may be related to the overheating problem you are also having. The most common problem is low engine coolant level and/or low engine temperature.

The radiator fluid in the radiator was green. This valve can cause the heater system to not work. A few tips troubleshooting your car heater.

Fixing clogging in the coolant or heater core. When you flush your radiator, the heater core gets flushed as well. Take off both heater hoses at the top of the engine, blow out fluid with low pressure.(5 or 10 lbs.) fill both hoses with the right radiator flush.

Get engine temp up to normal, feel both heater hoses. Will try a flush if i need to but want to get the gauge working first to make sure it's not the ecm not sending hot coolant to said heater core. Empty the radiator as per normal and thats it.

The 4.0 engines are well known for having terrible air bubbles after working on radiator, hoses, etc. While the engine is idling, feel for hot air from the a/c vents. Flushing out the tubes in the heater core will allow the coolant to flow more easily so there will always be warm coolant to heat up the air going into the cabin.

Flushing your car with vinegar will remove all these impurities, and your radiator will be back to good working condition. There are various reasons that could cause a clogged radiator. So, you need to get them replaced.

Position the control to discharge air from the a/c vents in the instrument panel. I just had a new frame put under it due to the frame recall and they had to drain the radiator but there was still no change. In cars five years old or newer is the most common problem is a faulty engine thermostat.

The amount of coolant in the system is too low.

Spoon Thermostat Thermostat, Radiator valves, How to make